| Last Modified: 11-29-2007 | 1.6 G | |
| Service Category: Vehicle Interior | Section: Seat | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM0000033MT004X |
| Title: SEAT: POWER SEAT SWITCH (for Rear No. 2 Seat): INSPECTION (2008 Sequoia) | ||
INSPECTION
1. INSPECT REAR POWER SEAT SWITCH
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
5 (BACK) - 6 (E) |
BACK |
Below 1 Ω |
|
5 (BACK) - 6 (E) |
OFF |
10 kΩ or higher |
|
4 (FWD) - 6 (E) |
FWD |
Below 1 Ω |
|
4 (FWD) - 6 (E) |
OFF |
10 kΩ or higher |
If the result is not as specified, replace the switch.
(b) Apply battery voltage to the switch connector, and check that the rear power seat switch illuminates.
OK:
|
Measurement Condition |
Switch Condition |
Specified Condition |
|---|---|---|
|
Battery positive (+) → 6 (ILL+) Battery negative (-) → 1 (ILL-) |
Always |
Illuminates |
If the result is not as specified, replace the switch.
2. INSPECT FOLD SEAT SWITCH ASSEMBLY (for RH Side)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
3 (FOLD) - 5 (E) |
FOLD |
Below 1 Ω |
|
3 (FOLD) - 5 (E) |
OFF |
10 kΩ or higher |
|
4 (RETURN) - 5 (E) |
RETURN |
Below 1 Ω |
|
4 (RETURN) - 5 (E) |
OFF |
10 kΩ or higher |
If the result is not as specified, replace the switch.
(b) Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
OK:
|
Measurement Condition |
Switch Condition |
Specified Condition |
|---|---|---|
|
Battery positive (+) → 2 (IND) Battery negative (-) → 5 (E) |
FOLD |
Indicator illuminates |
|
Battery positive (+) → 2 (IND) Battery negative (-) → 5 (E) |
RETURN |
Indicator illuminates |
|
Battery positive (+) → 1 (+B) Battery negative (-) → 5 (E) |
Always |
Lettering illuminates |
If the result is not as specified, replace the switch.
3. INSPECT FOLD SEAT SWITCH ASSEMBLY (for LH Side)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
4 (FOLD) - 3 (E) |
FOLD |
Below 1 Ω |
|
4 (FOLD) - 3 (E) |
OFF |
10 kΩ or higher |
|
5 (RETURN) - 3 (E) |
RETURN |
Below 1 Ω |
|
5 (RETURN) - 3 (E) |
OFF |
10 kΩ or higher |
If the result is not as specified, replace the switch.
(b) Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
OK:
|
Measurement Condition |
Switch Condition |
Specified Condition |
|---|---|---|
|
Battery positive (+) → 2 (IND) Battery negative (-) → 3 (E) |
FOLD |
Indicator illuminates |
|
Battery positive (+) → 2 (IND) Battery negative (-) → 3 (E) |
RETURN |
Indicator illuminates |
|
Battery positive (+) → 1 (+B) Battery negative (-) → 3 (E) |
Always |
Lettering illuminates |
If the result is not as specified, replace the switch.
4. INSPECT FOLD SEAT SWITCH ASSEMBLY (for Luggage Compartment RH Seat)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
3 (FOLD) - 5 (E) |
FOLD |
Below 1 Ω |
|
3 (FOLD) - 5 (E) |
OFF |
10 kΩ or higher |
|
4 (RETURN) - 5 (E) |
RETURN |
Below 1 Ω |
|
4 (RETURN) - 5 (E) |
OFF |
10 kΩ or higher |
If the result is not as specified, replace the switch.
(b) Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
OK:
|
Measurement Condition |
Switch Condition |
Specified Condition |
|---|---|---|
|
Battery positive (+) → 2 (IND) Battery negative (-) → 5 (E) |
FOLD |
Indicator illuminates |
|
Battery positive (+) → 2 (IND) Battery negative (-) → 5 (E) |
RETURN |
Indicator illuminates |
|
Battery positive (+) → 1 (+B) Battery negative (-) → 5 (E) |
Always |
Lettering illuminates |
If the result is not as specified, replace the switch.
5. INSPECT FOLD SEAT SWITCH ASSEMBLY (for Luggage Compartment LH Seat)
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
4 (FOLD) - 3 (E) |
FOLD |
Below 1 Ω |
|
4 (FOLD) - 3 (E) |
OFF |
10 kΩ or higher |
|
5 (RETURN) - 3 (E) |
RETURN |
Below 1 Ω |
|
5 (RETURN) - 3 (E) |
OFF |
10 kΩ or higher |
If the result is not as specified, replace the switch.
(b) Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.
OK:
|
Measurement Condition |
Switch Condition |
Specified Condition |
|---|---|---|
|
Battery positive (+) → 2 (IND) Battery negative (-) → 3 (E) |
FOLD |
Indicator illuminates |
|
Battery positive (+) → 2 (IND) Battery negative (-) → 3 (E) |
RETURN |
Indicator illuminates |
|
Battery positive (+) → 1 (+B) Battery negative (-) → 3 (E) |
Always |
Lettering illuminates |
If the result is not as specified, replace the switch.
|
|